The hardy hole is not centered in the anvil face.Ġ3.The hardy hole in this anvil is not centered on the face, making it difficult to use standard hardies and forks because they do not fit in the holes correctly. It is a steel plate and will quickly wear down your cutting tools and grinding wheels. It is good for beginners on a limited budget or light home projects. Not for experienced blacksmiths or those who are planning to do heavy work. Most hard tools are not centered on the face of the anvil. The anvil is very heavy and bulky for its size. It is hard to strike down in the hole when you need to strike downward. The hammer holder is located near the heel (back) of the anvil and not by the horn (front). If you are new to blacksmithing or low on cash, then this anvil will serve your needs for quite some time. In my experience, I have found if you take care to hold your work in a place without moving it around too much and you don’t strike too hard, it will last a long time. For those who are unskilled, you can quickly round or flatten your edges by hitting them on this anvil. Perhaps the biggest drawback is that the anvil face is not cast iron. The face is not soft enough to file flat again once these high spots are removed, so you will have to resort to grinding your edge off with a diamond grinder. It will quickly round out or flatten the high spots. The consequence is that it will not hold sharp edges very long. The biggest problem with this anvil is that it has a steel plate face instead of the traditional cast iron face. You should be aware of some things about this particular brand of anvil (by Ridgid) when purchasing one. It is not of the quality that more experienced smiths desire, but it works well if you work within its limitations. We at the TOS Crew have used this anvil for several years, and it has proven to be a good beginner’s anvil. It also comes with ridged leg stands that are adjustable, so you can set it up perfectly level on uneven surfaces or floors if needed. It has a heat-treated steel top and a solid cast base, which means you won’t hear any annoying clanging during use. This thing is built to take blows from a 50-pound sled and keep going like nothing happened. The Black 9 Forged Anvil by Ridgid is a heavy-duty beast of burden, and it’s packed with features for all but the most severe work. Ridgid 69632 Black Model 9 Forged Anvil Why Does It Stand Out to Us? The thinness of the top plate could be too much for some jobs.Ġ2.The open rear end for work-holding devices.♽imensions: 20.5″ wide x 13.25″ deep x 11.75″ tall at the highest point.The top is cast iron, with steel side plates, a steel post, and a stand made of steel.While it is fully functional and does well for most tasks, it may not handle some larger jobs. The biggest drawback we found with the Forged Anvil was the thinness of the top plate. This unit has everything you need to do some heavy hitting on small pieces of stock we love that it is fully surrounded by four sturdy side plates and has a partially open rear end for work-holding devices. If you are looking for an attractive, lightweight, and compact benchtop anvil for blacksmithing hobbyists, the Forged Anvil by Ridgid is a great choice. While it is fully functional and does well for most tasks, it may not handle some larger jobs.įortunately, this anvil also comes in a heavier version that comes with a slightly thicker top plate. Ridgid did a good job on this one, and we came home with our anvil that day. We also love that four sturdy side plates fully surround it we feel they added rigidity and strength in the critical areas. We were impressed by the high-tech look of these units. We were looking for something attractive, lightweight, compact, and functional enough to do the job.Īfter shopping around at local hardware stores, we came across the Forged Anvil by Ridgid at one of our usual haunts. We set out looking for a good benchtop anvil that would fit into our small shop. The front apron is equipped with a pronounced hardy hole and an adjustable tool steel post, making it easy to clamp just about any work holding device you can imagine. The partially open rear end allows for easy access to the hidden work holding section. Cast side plates surround the forged steel top plate for rigidity and strength where it matters most. This unit packs a ton of great features into one compact package. The Forged Anvil by Ridgid is like the Swiss Army Knife of anvils. RidGid 69642 Forged Anvil Model 12 Why It Stands Out to Us?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |